BabyTypeR
02-26-2010, 02:31 PM
DIY on how to convert! a 96-99 climate control
well ive been doin a bunch of readin up and ive decided to show some of my wrk that ive been doin to the car my car is original 96 but everythig has been converted to a 99-00
so i decided to finish it up by doin the climate control to a 99-00 as well
Mind you your doing this on your own risk so please becareful on wat u do and pay attendtion Good
thanks and enjoy it
Tools i used were
1) Socket Wrench
2) Sockets 14mm, 12mm, 10mm
3) Open Wrench 12mm
4) Socket Wrench Extension (at least 10in)
5) Extended Sockets 14mm, 12mm, 10mm
6) Philips Screwdriver
7) Pin/Hook Screwdriver
8) Pliers (to remove clamps)
9) A Friend.
10) Patience.
Conversion Requirements
1) 99+ Climate Control console with Climate harness (goes from console to heater core main plug)
2) 99+ Complete heater core Box
3) 99+ Complete Blower Box
4) 99+ Heater core harness (should be attached to the Heater core)
5) 99+ Center Dash vent (is contoured to position the vents to the right where the console has them)
6) Coolant.
this is how it was at first before i touched anything sloppy job but everthing got done right
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall003.jpg
well here's how i started off!
1.
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall002.jpg
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall005.jpg
2.
Then drop the steering wheel down
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall006.jpg
Then unbolted all the bolts to take the dash off this is how it look
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall008.jpg
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall010.jpg
FORGOT TO MENTION U HAVE TO CHANGE THE BLOWER BOX
WHICH ARE THESE BIG TWO BLACK BOXES
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall017.jpg
3.
Well this was the fitment on the old one OLD OWNER CUT IT UP =( my poor baby but she got a good one check it ;)
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall014.jpg
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall025.jpg
THE LEFT SIDE IS A 99-00 ONE AND THE RIGHT SIDE IS A 96-98 VENT
YOU WOULD ALSO HAVE TO CHANGE THE BIG VENT THAT GOES ONTO THE LITTLE VENT
HERES A PIC
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall023.jpg
4.
AND HERES WHEN IT FINALLY GOT ALMOST COMPLETED SO FAR SO GOOD =D:
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall028.jpg
YEA DECIDED TO THROW THE BLOCK OFF PLATE
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall029.jpg
5.
THE FINISH OF ALL WOOSH WATTA DAY THAT WAS BUT IM LOVING IT AND ALSO RELOCATED MY RADIO TO THE BUTTOM
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall032.jpg
there are also 2 plugs that u would have to run a wire to in order to make the Defrost work good its real easy i will show some pics on how it is done as well just forgot to do this and show how it is done but i will be updated ya with the info so ya can try it out =D
well ive been doin a bunch of readin up and ive decided to show some of my wrk that ive been doin to the car my car is original 96 but everythig has been converted to a 99-00
so i decided to finish it up by doin the climate control to a 99-00 as well
Mind you your doing this on your own risk so please becareful on wat u do and pay attendtion Good
thanks and enjoy it
Tools i used were
1) Socket Wrench
2) Sockets 14mm, 12mm, 10mm
3) Open Wrench 12mm
4) Socket Wrench Extension (at least 10in)
5) Extended Sockets 14mm, 12mm, 10mm
6) Philips Screwdriver
7) Pin/Hook Screwdriver
8) Pliers (to remove clamps)
9) A Friend.
10) Patience.
Conversion Requirements
1) 99+ Climate Control console with Climate harness (goes from console to heater core main plug)
2) 99+ Complete heater core Box
3) 99+ Complete Blower Box
4) 99+ Heater core harness (should be attached to the Heater core)
5) 99+ Center Dash vent (is contoured to position the vents to the right where the console has them)
6) Coolant.
this is how it was at first before i touched anything sloppy job but everthing got done right
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall003.jpg
well here's how i started off!
1.
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall002.jpg
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall005.jpg
2.
Then drop the steering wheel down
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall006.jpg
Then unbolted all the bolts to take the dash off this is how it look
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall008.jpg
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall010.jpg
FORGOT TO MENTION U HAVE TO CHANGE THE BLOWER BOX
WHICH ARE THESE BIG TWO BLACK BOXES
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall017.jpg
3.
Well this was the fitment on the old one OLD OWNER CUT IT UP =( my poor baby but she got a good one check it ;)
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall014.jpg
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall025.jpg
THE LEFT SIDE IS A 99-00 ONE AND THE RIGHT SIDE IS A 96-98 VENT
YOU WOULD ALSO HAVE TO CHANGE THE BIG VENT THAT GOES ONTO THE LITTLE VENT
HERES A PIC
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall023.jpg
4.
AND HERES WHEN IT FINALLY GOT ALMOST COMPLETED SO FAR SO GOOD =D:
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall028.jpg
YEA DECIDED TO THROW THE BLOCK OFF PLATE
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall029.jpg
5.
THE FINISH OF ALL WOOSH WATTA DAY THAT WAS BUT IM LOVING IT AND ALSO RELOCATED MY RADIO TO THE BUTTOM
http://i146.photobucket.com/albums/r251/jdmboy15/EVENTsandall032.jpg
there are also 2 plugs that u would have to run a wire to in order to make the Defrost work good its real easy i will show some pics on how it is done as well just forgot to do this and show how it is done but i will be updated ya with the info so ya can try it out =D