wiring vtec help!!

[Aknight23]

okay i did a mini me swap on my hatch and i need to figure out how to wire vtec. ive been told a bunch of different things but just cant figure it out. if anyone could tell me what wires go to what would really help out! thanks.

[rudsone]

find a diagram on Honda-tech...

[Rollin_Eg]

x2^^

[rudsone]

or get someone to do it for you.

If so.
Pm fatshlong. He stays in Peoria too...
tell him rudi with the white DA sent ya.

[Aknight23]

already followed honda tech nothing is up to date on that site.

[antjess123]

hey if you figure it out let me know. i just did a lsvtec swap with a b18 and b16 i need to find out how to wire up the vtec as well. if i figure it out i will let you know. if you get yours done please help me out as well. 480 335 2879 my names anthony thx!:type:

[ownercarry]

holy shit,
nothing is up to date on h-t?
did you see the search thingie?

3 wires.
pay attention.

ECU type: OBD1 ECU number: P30
A1 BRN INJ1 INJ1
A2 YEL INJ4 INJ4
A3 RED INJ2 INJ2
A4 ORN/WHT VTS VTEC solenoid
A5 LT BLU INJ3 INJ3
A6 ORN/BLK PO2SHTC O2 sensor (heating element)
A7 GRN/YEL FLR1 fuel pump
A8 (empty)
A9 GRN/WHT IACV IAC valve
A10 (empty)
A11 (empty)
A12 YEL/GRN FANC Fan Output
A13 GRN/ORN MIL MIL (check engine light)
A14 (empty)
A15 BLK/RED ACC (a/c compressor clutch)
A16 WHT/YEL ALT C alternator
A17
A18 (empty)
A19 (a/t trans only)
A20 RED PCS EVAP purge control solenoid
A21 RED/GRN ICM ICM
A22 (empty)
A23 BLK PG1 ground
A24 BLK PG2 ground
A25 YEL/BLK IGP2 to main relay and to gound for o
A26 BRN/BLK LG1 gound
B1 YEL/BLK IGP2 to pin A25
B2 BRN/BLK LG2 ground to shields for CYP & TDC
B3 (a/t trans only)
B4 (a/t trans only)
B5 BLU/RED ACS a/c switch
B6 (empty)
B7 (a/t trans only)
B8 BRN/RED PSPSW PSP switch
B9 BLU/WHT clutch interlock switch
B10 YEL/BLU VSS vehicle speed sensor
B11 ORN CYP P CYP -P
B12 WHT CYP M CYP -M
B13 ORN/BLU TDC P TDC -P
B14 WHT/BLU TDC M TDC -M
B15 BLU/GRN CKP P CKP -P
B16 BLU/YEL CKP M CKP -M
D1 WHT/BLU VBU Back Up Power
D2 GRN/WHT BKSW brake switch
D3 KS Knock Sensor
D4 BRN SCS service check connector
D5 (empty)
D6 ORN/BLU VTM VTEC pressure switch
D7 LT BLU TXD/RXD (data link connector)
D8 (empty)
D9 PNK ALT F alternator
D10 GRN/RED ELD electric load detector
D11 RED/BLU TPS TPS Signal
D12 YEL/GRN
D13 RED/WHT ECT ECT sensor
D14 WHT PHO2S O2 sensor
D15 RED/YEL IAT IAT sensor
D16 WHT/YEL VREF VREF
D17 WHT MAP Map Signal
D18 (a/t trans only)
D19 YEL/GRN VCC1 MAP 5V
D20 YEL/WHT VCC2 TPS 5V
D21 GRN/BLU SG1 MAP GND
D22 GRN/WHT SG2 TPS GND

if that doesn't do it for you, PLEASE have a shop do it for you.

[Aknight23]

i already know how to wire vtec its done been done for a while i was just wondering at the time of the mini me swap i figured it out in like 10 mins after i made this post