like the slips zach
|
looks like mine only redder, mine is basically pink :-\ fuck the arizona sun
|
wired a radio clip that was the wrong year....:facepalm:
|
Sold my swap going to pull it out and sell the shell with a new turbo kit has some goodies!
|
today i cut a dead coil off each of the rear springs on the wagon and added some washers to the rear uca's
|
getting ready to fire up the sander and take it to mine!
|
EF getting lots of love this week
ive been doing alot for my ef lately. didnt have a camera for most of the work but i did today.
-New drag suspension by prgress went in early this week been waiting for the track . - found an amplified 8"bazooka at my brothers crib and installed it in my trunk - today my girl and i hit up the pic a part for a tranny cable to replace my made in the us one -also found a rest pedal (dead pedal) from a crx so i pulled it and the studs that hold it to install into my dx hatch. ill post some pics of that cuz i found my camera |
CRX rest pedal install into a hatch
|
Took my axle back off and drove it everywhere, oh and raced a mustang and walked :)
|
i bet it feels so much faster
today justin finished tuning my car on 6psi. (i need a few things before he tunes for 15psi or whatever) tie rod ends, new bars for my traction bar, and a good boost controller with a wastegate fitting. |
took my hatch out for the first time since its been back together
|
|
This is what happened to me!!! Sucked
|
what did you end up using? DA?
|
yea da is the way to go. i have one here in tucson. lmk if you wanna come get it haha FOR FREEEE
also why dont you just modify the harness you have to run the new motor? |
I will take you up on that. As for the harness, because i really don't like wiring, if I can remember what I did with the harness I pulled out of James' car I'll try to use that but I can't remember if it even survived.
|
the car is an si correct? all thats needed is for you to buy some loom and about 40ft of wire
vtec pressure switch + vtec oressure switch - vtec solenoid + o2 sensor wiring i assume you have a chipped/tuned ecu so you wont really need a knock sensor wired you can make your own subharness or just use the harness that comes off of the obd0-1 conversion harness. i went with rywire and all my wires were long enough to run threw the bay and to all the areas needed to reach for wiring vtec and the o2 sensor. |
gave it a shower n shined up the shoes for the cruise
|
Picked it up from justins. Had a little chat about what needed to be upgraded/fixed for the e85 300+ tune that I have running threw my head.
After I picked it up I drove it up mt. Lemmon with all the guys from this website. It was my first time and it was pretty cool. My car is about as fast as I would want it to be with the tie rods being worn. It gets scary. Over all I'm the happiest guy ever right now. Oh and no overheating at all! |
I'm using James' ecu tuned with neptune but I'm sure it will need to be retuned for the new setup. Yes the car is an si but i get frustrated really easily when its comes to wiring. I'd be down to tackle it if I had someone there that had done it before, when will you be up my way again?
|
|
|
If anyone wants this hatch its dual point right now but I'm planing on putn ksports and droping my turbo swap in it let me know folks!
|
I'll be up this weekend. I'm down to get it running. I have obd1 clips and all for the dizzy. I'll bring the bracket up too. Idk which day I'll be up but pm me your number again and I'll text you once I'm up.
Oh and buy 40ft or 16g wire the thin solder for electrical (everyone I know buys gayass plumbing solder!!) heat shrink that works for 16 guage wire ( ace has good shit) and some loom if you want to use that probly shoulda pm'd you this but oh well |
Stoked that the swap is happening. Can't wait to see it in person.
|
Drove it around, fixed my bad tie rod end. I need an alignment soon. Found a damn hole in my radiator. It's my fault though. The radiator was badly in between the t bar and the wastegate and when I got on it I guess the motor moved enough to crush the radiator enough to make a little hole. Still hasn't overheated haha. I put water in the 2 times I drove it though
|
saw u rapin it when we were at lonnie"s house pulling his brothers motor..... still havent seen it in person looked good driving tho!
|
Nick your my hero. what radiator do you need? i might have one here.
Today I polished some rough spots in my intake and 94gaylude and I finished heat wrapping my DTR header |
|
this is nick, ineed a 2-5 radiator im gonna borrow a friends aluminum one for a bit
|
damn , sorry bro all i have now is ef
|
It's cool. You have a pm btw or will in a sec
|
|
|
took my jdm front bumper off because it was put on hag and was sagging
|
We took more than the front bumper of his ^^^^ car. :)
|
bought me a sexy stock si hatch, needs a little work. but replaced a radiator hose today.
|
Pics !!! ^^^
|
drove it around looking for a race to see where i stand but no luck. stopped overheating though:)
|
just get a new radiator already!!!!! ^^^^^
|
All times are GMT -7. The time now is 03:04 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
ŠAZHT.net 2004-2021